Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
The nrf905 has a CD (carrier detect) pin that is pulled high if the nrf905 detects another device communicating on the same channel. This can be used on the MCU for collision...
Hi,
In my application I am using Multiple App timers. Is there a way to prioritise these timers. Are there any draw backs in using multiple timers in "ble app".
Regards...
I want to set the resolvable private address ( RPA ) manually instead of letting softdevice do it. I went through documentation but I am not sure about it. I know that I can...
Hi
I am trying to put nrf52 device to system off mode, and wake up by button press.
If I do not enable the softdevice everything works fine, and button press wakes up...
Hi, I am trying to use the nRF52 to pass IMU information through BLE to a smartphone. We have a custom chip with the nRF52 and LSM9DS1 on the same board. I am able to program...
Hi!
Friday I can load the binary into PCA10040 (blinky example) ands works well. But today I load de binary but not works, nothing happen.
I'm used this example /Nordic...
It seems that I configured LFCLKSRC correctly, and advertising led flashes correctly.
Can I make any troubleshooting codes for Radio or Antenna?
Can I make some codes...
Hello,
Is it possible to erase only first N kB of internal flash memory before reprogramming nRF51 with JLink?
Lets say that I just want to erase first 64 kB of flash...
Github said it works in sdk8.1, But I place it under *nRF51_SDK_10.0.0_dc26b5e\examples* It works well in the demo board. Question,Can it be used in sdk10?
What I want to...
Hi,
referring to the SoftDevice Specification, S132 Softdevice vx.0, paragraph 15.2 (Attribute table size) I wonder how one does work out the size of the attribute table...
Hi,
Hope this is not a duplicate post. I am using nRF52832 and SDK Ver 11 and am facing the following issue:
After configuring the UART and SPI, I put a string e.g....
Hi
Today I have recieved the new nRF52 Development kit PCA10040. I have downloaded the latest version of SDK nRF5_SDK_12.0.0_12f24da working with ANT_s212_nrf52_2.0.0....
I can't build ble_app_proximity_pca10040 example due to uv5 core size limit. One user suggested that I port the old device_manager to SDK 12 proximity example to reduce core...
Hi guys,
I am using the nRF52 DK with IAR 7.70.2 and SKD12.0.0.
I notice that the blinky example has 2 versions for the nRF52 DK:
a) blinky_pca10040...
