My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
HI Teams
I found in the datasheet that the UART, I2C, and SPI on the nRF5340 share the same set of IDs. Does this mean that these three buses cannot be used simultaneously...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
I am currently evaluating the Channel Sounding functionality for indoor localization. I would like to check how much Energy my Initiator and Reflector consume for...
Hello, I am currently developing on a custom board based on the nRF7002 + nRF5340. The SDK version is v2.8.0, and the development is based on the BLE Provisioning example...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
Hi Team,
I am working on a project where we are using nRF5340/nRF52840 uC IC from Nordic. from past 2-3 years we were using this software hassle free but now due to to some...
I am using NCS 2.9.0 and latest extensions for VS Code.
To reproduce, use Mac, create a new app from Blinky sample, build it and open "prj.conf", then wait a few minutes...
Has anyone else had problems with adding build configurations for workspace applications using the VSCode GUI interface? Initially I clone the repo using CLI-based west commands...
Hello,
I am fairly new to the development with nRF and am having problems getting sensor data from a connected BMP280 to the nRF5340 audio dk.
The first thing I did...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
