Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi
I have a question when I use the l01+.
I donn't use the Auto acknowledgement and Auto Retransmission, interrupt does not reflects on the IRQ pin and leave the IRQ...
hi,
i try to analyze the sdk sample with the standard(Server) ,ie : basic battery service
how to build GATT Requirements and Service Characteristics with the...
Just got the RF51822 PCA 1001 dev board and followed the instructions in SDK 4.4.1 and downloaded the Keil Lite tools from the ARM website.
BUT, didn't realize Keil has...
Hi,
how do I evoke Gazelle on NRF51422? According to specs NRF51422 supports both ANT and Gazelle although on SDK for 51422 the gzll folder is missing. It is present though...
Hi ,
I am using PCA10001 board.
Now i want create 4k buffer in RAM. Which is good way allocate memory to 4k buffer.
Can i use dynamic(malloc function) or static memory...
Assuming the system is composed of one device using nRF51822 and iPhone/PC,
If we want nRF51822 detectable by iPhone/PC so that iPhone/PC can connect nRF51822 when they want...
Hi!
I have been using Bluetooth 2.0 modules for years and now I want to take the step to 4.0/BLE. Previously I used Free2move modules with built in stack. Very simple, make...
I have the nRF51822 development kit (with the new hardware revision QFAA or something), and I am using the Master Control Panel with the new 0.9 firmware for the dongle. ...
Hi in my case,
i pressed gpio button for one time it will do one event.
and for double press it will do another event . how can i do this one,
Regards
Balaji
Hi
In my case i have both 3 gpio interrupts and 4 rtc1 interrupts and have some timer 0 and 1 interrupts
also. how to set priority for all these interrupts in both while...
Hi Guys,
I am planning on using the nrf24l01+ to send data with a payload which is larger than 32 bytes, I was wondering whats the fastest way to transmit these packets...
Hi,
In the nrf51822 SDK examples, there is an example of radio_example which is used for send data and read data. I want to konw that if one module send data and then...
Hello - I am trying to port code over from a development kit over to the WLCSP nRF51822 on a custom PCB.
I am able to connect/bond with my device fine, however I am having...
Hi,
we're using an nRF8001.
Trying to find the relevant Bluetooth Specifications, we found the following mess (pardon my french!):
Core Specification 4.0, 2300 pages...
