Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello,
I am currently for a quick solution to test NRF24LE1 compliance to FCC. Can you provide me with any code if possible? As i could see from the website only an application...
Hi,
We can utilize the 31 bytes of advertising packet as well as 31 bytes of scan response packet which in total makes it 62 bytes of advertising data. What is the effect...
Hi dear Nordic Engineers.
We going to move from FN-LINK (Realtek) I.C. BLE to nRF52.
FN-LINK uses HCI (UART) BLE the Interface to communicate with our embd. LINUX.
How...
Hi all,
I'm using pca10040 board with sdk version nRF5_SDK_11.0.0-2.alpha_bc3f6a0.
There i'm using example code of spi handling. Instead of nrf_log_printf i changed...
Hello,
There's any known issue realated with DFU and Android 7.0? When we try to update firmware with nRF Connect or our APP we get an error (hex file error), but when...
I am going to develop an application on nfr51422 that requires very low current consumption. Basically we plan to make the nfr51 to "sleep", and it will wake up constantly...
Hi
I have firmware uing SDK 7.1 and SoftDevice 110. There is prepared bootloader for DFU, and update by very old nrfToolbox app works fine. But now I want to update this...
Using the Data Length Extension (DLE) feature in BLE v4.2, two nRF52 dev boards can achieve a maximum throughput of almost 800 kbps. I tested DLE with an iPhone 6 and the...
I am new to nRF ICs.
How to get 32.678KHz clock out from a pin? Is it possible? If yes, from which pin and how to configure it?
I am using 32.768KHZ external crystal fro...
I have designed several boards for the nRF51822-QFAA, namely with/for the Waveshare Core51822 module.
While one is working as expected - namely my "Orchid Lamp" (see links...
When softdevice S110 is used then bonding is not occuring (via nrf connect app to nrf51).but both devices get bonded when s130 is used?In Nrf connect app key matching failed...
Hi,
I have a working project where I use PWM driver with LEDs on the development board. I make use of the d52_starterkit.h where I have the following definitions:
#define...
