Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
Hi in my project I am using nRF5_SDK_11.0.0-2.alpha SDK, s132_nrf52_2.0.0-7.alpha_softdevice. and nrf52 DK board(PC10040).
My issue is, when I run the ble_app_uart example...
Since PStorage has been removed and replaced by FStorage on SDK12, why is PStorage still listed as Experimental in the Documentation? It would appear that if you are removing...
Hello,
I am aware that according to IEEE standards RSSI value that chips return is not officially related to mW/dBm. However the values returned by your chips seem to be...
Hello,
I am trying to use timer with Bluetooth application . I want to provide precise time stamping using timer for each bluetooth event. But program execution stucks...
Hi,
I'm using nRF5 SDK V11、s130_nrf51_2.0.0_softdevice. My application has added the DFU service . I download application,softdevice and bootloader to nRF51822 AC, the...
i m using pca10028 with gcc tool chain setup in windows...now i m using sdk 8 and work inside ble_uart code...i was add rtc1 inside that code sucsessfully but now.. when device...
Hello,
I am currently testing the nRF51 series as a possible upgrade to our products that use the 24L01P. For testing I have the nRF51 dev board setup as the PRX and a...
I'm using SDK 11 on my nrf51 chip. I'm trying to output a 120hz pwm but it doesn't seem to be producing at 120hz. I have a 120hz signal i'm trying to match and it blows pass...
Dear Wang,
I am unable find any documentation and board Initialisation code on how to change PIO from analog to digital output. but can't seem to locate the setting.
...
