I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I need a code example (e.g. Health Thermometer) that runs on the Beacon Kit. I have tried several combinations of soft devices and code examples, but I can't get it running...
Hello,
I started implementing a project with the device manager. I am using the S120 as central.
I am able to connect to 3 peripherals at the same time (also nordic nrf51822...
Hi,
The environment is Ubuntu 16.04 running on parallels on a mac pro.
I am following all the installation instructions and I get no errors, except that the opus driver...
Hi,
Today, i try to use the UART SERVICE from nordic on both smartphone and NRF51.
I succeed to send data between the two.
But now, i want to send data longer than 20...
Hi,
Using SDK12.1 with nrf52. Have SD and bootloader on the device and trying to load application via BLE DFU.
It randomly gets stuck. (see attached screenshot)
And...
Hello,
I have some trouble to use the Secure Bootloader example, which comes with the
nRF5_SDK_12.1.0
I installed the latest nrfutil and hexmerge. I can compile the...
This piece of code appears in all IoT SDK examples:
eui48_t ipv6_medium_eui48;
err_code = ipv6_medium_eui48_get(m_ipv6_medium.ipv6_medium_instance_id,
&ipv6_medium_eui48...
Hi, I am using the nrf uart app to communicate with a smart phone and the NRF52. I am trying to detect whenever it is sent a value between 0 and 60 from the phone, and save...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
I want to use ATMEGA 328 to send a packet over to the chip as follows:
SPDR = packet ;
Can some one kindly post what the content of this packat should be ?
is it possible...
hi,
i am working on FDS. here i am able to write number of records and also able to read them back.
but while updating i deleted one of the old record and writing new...
Hello,
I have some problems with UART communication with my nRF51 DK.
When I connect it through USB cable, all is ok. But when I connect pins: P0.09(TXD), P0.11(RXD) to...
