I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I saw following code configuring about permission of charateristic value R/W.
it's in uart example of SDK 11.0.0.
static uint32_t tx_char_add (ble_nus_t * p_nus, const...
Hello
could anyone help me how to setup pipes for my characteristic, i need to recieve/transmit data to UUID of my characteristic, and recieve/trasmit to ClientcharacteristicConfiguration...
I have a ADC interrupt that occurs every 17ms and which copies the samples into a global static array, after which GivesFromISR to a binary semaphore so that the samples may...
please anyone answer for how to configure the digital input to make active the digital output in nrf52832? if give example program means it is much better
Hey!
I am working on NRF51822-QFAC, with the help of SDK 12.2 with the aim of scanning my bluetooth speakers and mobile phone.
For the same, I have loaded the project...
I want to change rx to tx mode and back after recertion my master NRF24l01 packet on NRF52 with esb, how to do it?
I tried this but it doesnt works:
void nrf_esb_event_handler...
Hello,
I am using nrf51822 and supply is provided through rechargeable battery. Please review my schematic and suggest changes if there is any.
Thanks,
Shailav
I used the following code to verify the working of the clock (at P04) of nRF24le1.
I used a 4.7K pull up resistor with a VDD of 3.3V, which was output from the nRF.
Note...
Hello,
I'm using nrf51822/s130/sdk12.1.0.
Before adding BLE code there's no problem in writing inner flash.
In main I just added below ble_app_uart codes(not modified...
Hi,
I have Wireshark version 1.10.14 and sniffer version 1.0.1. I send the data out from PCA10040 with connection interval of 7.5 ms and packet throughput of 200Hz using...
The pulldown on the SAADC is 160k. Is it ok to create a resistor ladder by adding an external resistor of, say, 400k, enable the internal pulldown and then input a higher...
Hi NordicSemiconductor's community,
I have a basic question about connection to a BLE peripheral.
I use the SDK_10.0.0 and s110_v8.0.0.
I want to know how to implement...
how to change RX and TX operations ?
i wrote next code:
#include "nrf_esb.h"
#include <stdbool.h>
#include <stdint.h>
#include "sdk_common.h"
#include "nrf.h"
#include...
