Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Using nRF52DK and working through the getting started tutorial I could not get the ble_app_uart example in SDK 12.2.0 to work. It compiles without errors or warnings and appears...
Hello,
Trying to make my own project to test buttons and LEDs for educational purposes, I looked at this . Using uVision, I tried to replicate the included modules of that...
i am testing the ble_uart programme. i am using the nRF51822Ek and soft device s130_nRF51_2.0.0 and nRF5 SDK v12.2.0 and keil uvision5 and nRF tool box (android).i am using...
Hi
I have the PPK, and I see it needs either a JLink or a Nordic DK board to act as the interface to the PC.
I have a nrf52832 dk and also nRF52840 dk, so I was going...
I made IAR work with nrf52 in monitor mode debugger. I also would like to try this to nrf51. I found nrf51 doesn't have DebugMon_handler......Please confirm can I single step...
Hi,
I am working with nRF51 for my application. I do not use softdevices. I need to have a random variable in my code. I have read Reference Manual and I have found that...
Does nRF51822 have battery monitor?
pg 45 of datasheet says specifies "Absolute error when used for battery measurement" at:
Internal reference, input from VDD/3...
In the nrf52 OPS datasheet, for NVM and flash programming electrical specification (page 41) it has "Amount of writes in a block between erase" and Minimum for that is 181...
Hi all.
I need some suggestion how to use UART module in the nRF52 using nRF5_SDK_12.2.0 and the softdevice $132(it would affect?)
I would like use RX to receive information...
Hi.
Didn't find an exact answer for my question.
I'm using the ble_app_beacon example on my custom board based on nrf51822. While powering it from a coin battery, I measure...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...
Help!! I need to implement a dc motor position control and i have problem reading the encoder (too fast). I have seen that nrf51822 has a qdec peripheral. Any suggestions...
Hi,
I wanted to know if the UART pins can cause any issues if kept connected to usb (Rx/Tx pins stable to 3.3V) and directly to the GPIOs of the nRF52, while performing...
I've come across the following situation:
We have a device (nrf52) which uses fast advertising with whitelist after it has established a bond with a single phone. When...
