At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I'm developing custom board of nrF51822 CEAA (256k, 16k)
I set my bootloader ROM, RAM just like below
as I understand,
Firmware size should not larger than...
hi,
i just ask about nrf52832.
im using it with keil compiler and trying to divide the memory section (it that will be update and not)
but i have hard time to do with keil...
I'd like to log some debug stuff to a mobile app over BLE, when in a connection, using the NRF_LOG library and the Nordic UART service. I have this working just fine without...
I'm trying to write to specific address on flash memory (data region) for debug purpose using
nrfjprog.exe --memwr 0x3B820 --val 0xAA000000 --verify
but when I read...
So I'm still trying to get my way around the DFU service implementation, and I'm currently having trouble with the first step, which is to enable the control point notification...
Hi.
This is a bit of a combo question:
I recently got the nRF52 10040 and I'm trying out the included examples on uVision5.
I only managed some examples to...
I am working on BLE Applications, I have tested with different devices like Nexus, Moto, Samsung, LG(ble V 4.0). I am getting the GATT Error 133 in Samsung Devices alone(Samsung...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hi,
I have an nRF52 chip that has likely exceeded the flash endurance limit.
I am observing that after an ERASEALL, not all bits are erased, but after retrying ERASEALL...
Hi, does somebody know why in Segger embedded studio program goes to ses_nrf51_startup.s line 35 ISR_HANDLER NMI_Handler and sits there. I'm trying ble_app_cscs_pca10028_s130...
I only have Bluetooth 4.0 scanners and I bought nrf51 dk with 51422 device (10028) that seems to work as 4.1 Bluetooth. I tried sdk12 s130 and sdk8 s110 beacon examples my...
Hi,
I'm trying to program the bootloader together with an application+SD132 3.0 on the nrf52, but my device gets stuck with the bootloader when I finish programming it...
Hello, I used s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
Is there any example to study the central bond?
I use the examples->ble_central->ble_app_uart_c, the following...
