We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi Nordic
I am using ESB_DPL protocol between two 51822 to do RF communication.
First i put two device very close, works very good, no packet loss, then I moved the...
After spending substantial time without luck I will drop my question here.
Setup
nRF5_SDK_12.1.0_0d23e2a -> bootloader_secure debug target
nRF51 & nRF52
IAR...
Hi,
I am using simple ADC peripheral to read internal battery voltage(standalone). I am using two custom nRF51822 boards. One of the nRF51822 board is made by nRF51822...
Hello. I just started learn ble module and some confusing about ble_app_uart:
in file ble_nus.c we have function on_write this function calling when trigerred BLE_GATTS_EVT_WRITE...
I am developing a android app for firmware update on my device. I used buttonless dfu example to switch from application mode to bootloader mode, I write value 0x01 to the...
I'm trying to track down who is erasing and programming 0x800..0xFFF.
Does the SD_MBR_COMMAND_COPY_BL modify 0x800..0xFFF?
I inserted a CRC32 at the end of the MBR ...
How should we comprehend the nature of PPI, when dealing with radio interrupts?
For example, if I point radio event handler call back ( of this type:
static nrf_radio_signal_callback_return_param_t...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
