Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
we try to use static passkey protection on our devices.
we use nrf51 sdk12 with s130.
We read a few threads for setting a static passkey like here , here and some...
Hi guys, I'm migrating my SDK 10 project up to SDK 12. There are quite a few new configuration files and setups. In order to enable app_pwm peripherals I enabled the proper...
Hello when I tried to use IronPython with MasterEmulator.dll in example as described in documentation. I got following error:
c:\Program Files (x86)\IronPython 2.7>ipy...
I'm tying to read and write external memory using Spi bus
when I flash only the softdevice and the app, the program works fine
but when I flash the bootloader, the program...
I'm trying to flash the bootloader on an nrf52 device. the microcontroller is detected successfully with segger. but then when I flash the bootloader given with sdk11 (dual...
Hi,
my device : nRF51822 with sdk 10.0
Before I talk my question, let me make clear.
When peripheral connects to iPhone, it's on iOS's setting too but it doesn't go...
Hi nRF support,
In order to minimize the code size, I tried to enable define the macro BSP_SIMPLE, then I got the below error:
*** Using Compiler 'V5.06 update 2 (build...
Hi I'm trying to perform update (DFU) of my application using Master Control Panel 3.10.0.
I'm connecting, discover services (see DFU service available), then press "DFU...
When I connect the Nordic 51822 DK to the PC, I can not detect the device using
root@riot-VirtualBox:/home/riot# hcitool scan
Device is not available: No such device
...
Hi,
EX_1.rar
Can I define "non-const" variable for writing data via I2C using "APP_TWI_Write" function? Similar for read.
When using External "EEPROM" one should...
Do I need to manually go though every HW exaple in the examples in sdk12 and cut and paste all the little bits that I need or is there any other way?
I have a custom board...
Hi,
I'm using the nRF52 as a master and an external RF chip as a slave. After configuring my spi bus using nrf_drv_spi_init(&spi, NULL, NULL), in my main loop, how do I...
I have used nRF toolbox to update bootloader and firmware to my nordic device. I was previously using iOS9 (I believe 9.3.5 - whatever the latest version was before iOS10...
Firstly,I used ios9.3.5 to DFU successfully,
But when 9.14(ios10 was pushed),then my iphone6s was updated to ios10,
finally DFU failed.
The device can enter in the DFU...
