Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
We followed this link devzone.nordicsemi.com/.../ , we loaded zip file in mobile(android 6.0.1). We are able to select device, we are not able to select file(Zip). The issue...
as I found the sample code in sdk12 , the bootloader is quite different with bootloader in sdk11,
event uuid has got changed, is it possible to be compatible?
dual bank...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello to everyone. I'll need to use ble things with pwm. I'm trying to play around with pwm library it's ok, but it's build only on erased chip, trying to flash it into chip...
I try use the FICR information to identifier nRF51. but found some interesting staff when i read 0x10000000 first 16 bytes by SWD memory read.
when I power on read. it return...
Hi,
I started my project from the “BLE Characteristics, a beginner's tutorial” I download this project and add it to my SDK_11.0.0_89a8197 .
Then I started to modify the...
I am using the FDS functions to save needed data to flash and retrieve it when needed. The init, writing, and reading all function correctly. However I am running into trouble...
Hi,
I'm having some issues when trying to make a HID device work with Windows 10. It says 'Connected' but then changes to 'Device Error' a few seconds later. I get 'Error...
Hi,
Im tryin to use the ble_dfu service example from SDK12, I get DFU SERVICE NOT FOUND when trying to update from Android.
Any suggestions what to look for?
I use...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I am using the NRF52 to send sensor information over bluetooth using Nordic UART Service. Can the same service be used to send strings?
Thank you.
Hi,
I'm developing to nrf51822 mcu, using a s130 softdevice.
I'm using a BLE example code.
I get an interesting problem - when the mcu receives 2 reports (that are...
Hi,
we are thinking about using the NRF52 with the BLE SoftDevice in a security relevant application. As the SoftDevice is not available as source code, no reasonable security...
Hi all!
I want to check work of AES encryption.
Some code on 51822:
uint8_t aesKey[]= {0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39,0x30,0x31,0x32,0x33,0x34,0x35,0x36...
Hi All,
I have a problem with the function sd_ble_gatts_hvx().
I have no return value when i call this function and i don't understand why ?
I have a function where...
