Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Using nrf52 DK , SDK 12.2 , and armgcc.
I want to use BLE_UART but I also want to bond.
I started with the BLE_UART example code and added peer manager and FDS.
I...
I've been trying to track down a bug where a couple of my Central test devices, a Nexus 5 and 7 (Android 6.1), won't send a connection request to a peripheral they're bonded...
Hi
I have a problem on testing the HRS examples on SDK12.2.0.
When I use a android phone, running on version 6.0, using nRF Toolbox version 2.2.1 App, to connect to the...
Hi!
After reading nRF24L01 product spec, I'm really unsure:
Spec. says: "The input signal should not have amplitudes exceeding any rail voltage."
"rail voltage" it's...
Update 1/27/2016
Just reviewing again the pins + schematic; I am using the following pins:
SCK P0.07
CS P0.08
MOSI P0.06
MISO P0.05/AIN3
Looing at the...
After i test a lot of possible configurations for nrf24L01+ based on the documentation, i didn't come to the right setup for all the nRf24L01+ registers to send data from...
Hi,
I'm using Windows and I am following this tutorial.
I am at the point where I need to write make at the example project.
I get this error
as warned in the...
Hi,
I'm trying to get a general idea of how the radio will perform near the bottom end of the supply range.
Our product concept is currently designed on a system voltage...
Hi,
I stuck on SOFTDEVICE_HANDLER_INIT in example code on nRF DK PCA100028 within debug.
It is example code from SDK 7.1.
How Can I solve this?
Why Nordic's SDK...
Hello,
I am developing an an system and I am at the stage of optimizing for power.
I using NRF6707 ( Very helpful !!) to measure current.
I cut SB9 of NRF52 DK and have...
Hi,
Can I try to discovery services for the next connections while it is performing for the other connection?
I use "ble db discover" manager.
And I cant find this...
I'm using nRF52DK and SDK12.2.0.
Trying to change MTU size.
When I modified app_nrf_uart example as below
#define NRF_BLE_MAX_MTU_SIZE 103
Then infinite reboot...
I am working on a project and have successfully implemented single channel PWM to dim leds (using a transistor FET).
The pwm init code is below:
uint32_t err_code;
nrf_drv_pwm_config_t...
image description (http://)when i try to flash the led binky programme to nRF51822 Ek. i am getting device error and LED also glowing continuously.
1.this device error was...
