Our nrf9151 boards are getting stuck when nrf_modem_lib_init() is called.
We just see this line. Usually, the device gets past it in less than a second.
[00:00:00.376...
Hi,
I would like an nRFX example on how to set up DPPI using single in (1 Event) and multiple out (2 Tasks). I have previously done this using the fork functionality in...
Hey all,
Every time I flash, I get the following error message:
Error: One or more batch tasks failed: - [Probe] Device error: Memory access error at 0x00000000. Probably...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
Hello,
Yesterday, I received a new Power Profiler Kit 2 device directly out of the box, and unfortunately, it is not detected by any PC.
Symptoms: - The green LED blinks...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
I add my own codes in nRF51-ble-bcast-mesh-sdk-8-support project,
then I find that if device_flash_init() is compile to this project,
the program cannot finish rbc_mesh_init...
Hi,
I have app + bootloader in one packet. On Android nRF Toolbox both can be updated in one step using Distribution Packet option. Is this possible on iOS?
I know it...
The BLE Central tutorial (S130 based) does not connect to my peripheral. My peripheral connects fine to the Android MCP and the 128-bit service UUID is what I expect.
I...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
Now I have generated bootloader.hex used by /DFU/bootloader.
After programming bootloader.hex and s110_nrf51_8.0.0.hex,the device's name changed to DfuTarg.
But when I...
Hell,
Wich BT dongle I can use to dawnload data fro board with nRF51822 chip on it?
If thear is App. to use for comunication and dawnloading data from electronic board with...
Hi,
I am using nRF51422 with s130 soft device along with SDK v9.0. I am trying to read/write flash memory using pstorage module. I am using BLE nus service for data transfer...
each time I start my program (nrf51 device) I get an error code I save in flash to check it at next restart. I can read error code 0x20
is this a correct error code and what...
Hi,
I try to generate a PWM signal on PCA10040 with the nRF52832. To do that I copied the code from the Product Specification into my application, but nothing comes out....
Hi,
I made my prototype board using the nrf51822 chip. for this prototype i use an on-board connector + external programmer to flash the nrf51822 chip.
that's work...
I am looking ahead to the time when I will graduate from using the nRF52 development board to building a custom device with the SoC. The PCA10036 chip will obviously not be...
Hello,
I am almost finishing developement of a BLE module using nrf51822.
For mass production, I hope I can program Softdevice/Bootloader/Firmware to 10 nrf51822 using...
Hi
I want to receive and send a lot of data in a short time (connection Intervall is set to 20ms). And I get the App-Error 0x3004.
I found this definition for the error...
