Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi, im trying to update the firmware of a nrf52 using dfu ble. For example, have a blinky example running and switch to a blinky2. Can anyone know if this is possible?
Hello,
I am doing a search in the Eclipse to find texts, I noticed that Eclipse is not finding any of the texts from the Include files. I did a google search on this issue...
Hi,
I use pstorage to allocate 32bytes of memory with 2 block, means each block having 16 bytes, when I write 16byte data into block_0 portion, I am not able to go to the...
Hello,
I use the Segger J-link software with my PCA10001 and recently updated it to last version (v.5.1). After install it asked me to update the firmware to the last version...
Hello,
I'm trying to flash external nrf51422 module.
I want to flash both softdevice and application. I used below commands:
mergehex -m %SOFTDEVICE_NAME% %APP_NAME...
I want as much control over advertising as possible. Barring that, I want to understand why the softdevice automatically goes back into advertising after a GAP disconnect...
Hi,
Assume that we want to send a data array by putting it in consecutive advertisement packets. I know that data update has to be done by calling ble_advdata_set(...)...
Hi
I'm trying to implement battery level on my custom profile.
So I used battery.c and ble_bas.c files for the battery service from nodic's sdk nrf51822_v4.4.1.31827....
I have make over your bootloader example to create my own without BLE support in bootloader (new programs are send in application instead of in dfu bootloader). Bootloader...
Having some trouble using the NRF52 as RX and nrf24l01+ as TX. The NRF52 receives the packet, but for some reason it always says CRCerror.
Anyone ever tried to use NRF52...
Hey Guys,
In my custom board I need to use two different I2C bus and one SPI.
At the moment i'm using twi_master to comunicate with one of the TWI bus,
but to switch...
I have several nRF6930 beacon kits. Some have a sticker indicating they have a PCA10006 board, on others, the sticker indicates PCA20006. All PCBs are marked 400059 0138RUBR...
