Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi
I have a MCU with an external sensor connected via SPI sampling data at 1000Hz.
Using the nRF8001 with REQN and RDYN lines is making trouble. The REQN line is pulled...
I am trying to accomplish the following very simple task: use the broadcasting function of my nrf 8001 to send up to 19 Bytes of data over the air (connectionless).
I tried...
I need to create a backlight fade-in/out effect. For this I'm using the latest nrf_pwm lib form here together with the S110 Softdevice. Using the scheduler and an application...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
Hello,
Im using the master control panel app from nordic to use the DFU.
I can only once upload the application over DFU on my nRF51422. Because after the upload is...
Hi,
I have been trying to connect to a proximity tag and stay connected but with no luck. What happening is that the unit connect does its thing and then disconnect with...
I use a OLIMEX nRF8001 module with ATMEGA328 at 3v3. Using the "helloWorld" serial example sketch, I measure a current of approx 400-600uA. However, if I use the calculator...
Hi Nordic
I want to test parameter about output power 、sensitivity and so on ,but we have not software tool . Could you tell us how to test and provide tool to me .
...
Hi,
How to set user description descriptor to a particular attribute? I have created one primary gatt service with more than four characteristics, when is see it through...
Hi,
Master device is whole the time in receive mode and I have a problem with read data from device which address is in Pipe1. IRQ appear and status is 0x4e and FIFO status...
Hello, I bought the nRF51822 Development kit and the nRF6700 starter kit and I'm having trouble finding tutorials on how to use the 2.4 GHz radio mode on the nRF51822. Can...
Hi everyone,
I have some strange behavior with a central peripheral combination. My central subscribes notification on the peripheral. This has a limited TX-Buffer for just...
Hi,
I am developing the nRF51822 for the BLE device application. For the data delivery I am implement this function based on "button_radio_example(Tx/RX)" example code. It...
