Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
condition:i am using the nrf51_adk10.0.0,and i want to enable the NRF51422 as a central role.,so a program the sd130,and i download the application into the board(ble_app_uart_c_s130_pca10028...
Hello,
I am using nRF51822 to build a product and employ 3.0V battery as power supply and system works on DCDC mode. I need RTC counter to do real time tracking. My question...
Hi,
I am developing a glucose application using nrf51822 chip.
Now i want to go for mass manufacturing.
All my devices are advertising the same name.
I want to identify...
Hi all,
I was testing with a new nRF51 Dongle recently and am finding that it disconnected from any peripheral after 15-18 seconds. Generally a little while after a Connection...
I had a PWM question ( here ). It was recommended that I install SDK 10 and use the PWM files from SDK 10. I installed and copied the PWM files from 10 to 9 and opened my...
Hi, I've compiled program from this link:
developer.mbed.org/.../
The problem is that I can't connect to my DK by nRF UART 2.0 app, probably because not every UUID is...
I am working on adding a timer in the ble_app_uart sample, aiming on disconnect with device which doesn't send any data in specific time, such as 5 seconds.
Now I have...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
