I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
Hello,
I want to add uart debug support to the BLE DFU bootloader (nRF51822, S120, custom board).
Therefor I increased the possible size of the bootloader (start 0x39800...
Good evening and a happy new year to everybody.
Now it's time to work again, and I already stumbled about a little twouble while implementing a peripheral with concurrent...
Hey guys,
I'm designing an antenna for our open source sensor beacon, RuuviTag: http://ruuvi.com
Because we're using 1/4 wavelength monopole antenna, I'm considering...
for ble, scan of central device can get the RSSI value of the advertising device, but the inquire can not.
Is it right?
what's the different between them?
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
Hi guys, I just want to share my iBeacon code (over s110) developed on nrf51 dev board under ubuntu. It works fine but please feel free to improve it and share it!
I developed...
In some case sd_nvic_SystemReset() can not reset?
nrf51822 S110.
for example:
void main(void)
{
sd_nvic_SystemReset();
do something;
}
It can do somthing!!
So sd_nvic_SystemReset...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
