Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do to resolve this issue...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hello,
Used environment:
Board: nrf9151dk_nrf9151_ns
SDK Toolchain: v3.0.2
IDE: Vscode
I'm trying to test the LIS2DH sample using the nrf9151DK and the STEVAL...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
Hi All,
Is there a way to disable currently running Noric BLE stack and port 3rd party BLE stack also enable new stack on PCA10001 (nrf51822 dev kit). We have our own stack...
Hi all
I tried to add a vendor specific 128bit UUID with the function sd_ble_uuid_vs_add. It worked and I received the custom UUID type (0x02). Afterwards I tried to add...
Unable to Install or Launch nRFgo Studio Win64 1.18:
Downloaded "nrfgostudio_win-64_1.18.0_installer.msi
Installed package on a 64-bit Windows 7 PC as a 'regular...
I'm playing with the SDK 8.0 HRS peripheral example.
There is a config folder that contains device_manager_cnfg.h. But this isn't being built into the project, the version...
Hello,
I am currently trying to write my frist few lines of code.. I started with the ble_uart example and then mixed in some code from the spi_master example.. I wanted...
Hello,
why did you chose to remove the S130 1.0.0.3-alpha from the relasenotes and merge it with the latest version? I don't think that's the way it works. Now we have...
Hi All !
I was read many posts about this function and do not understand how to check if all data is deleted.
In my situation I do:
Start advertising for bonded...
My devices in the field have firmware that saves an error code when it gets thrown and then sends it to a central so that I can see if there are errors with devices in the...
Hello,
I am using the sd_flash_write function. If I use this function without the nrf_delay_ms() function (see code below) the data is not being written.
sd_flash_write...
I would like to know if it is possible to log realtime sensor data to flash while advertising. I would like to have a device which transmits real time ECG data over ble UART...
Hi
I am struggling to change the device type on examples setup for nrf51422 to nrf51822.
If I change the setting in "options for target"/device I get the failure message...
I changed the multilink central example to some custom code. However, it seems like I've run out of space. But I don't under stand how this is possible because I selected...
Using gcc-arm-none-eabi-4_8-2014q1-20140314
Using nRF51_SDK_8 Using nRF51 dongle
Build in nRF51_SDK_8/examples/peripheral/blinky/pca10031/s110/armgcc succeeds...
