I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
Hello,
I am trying to get a lower connection interval from iOS. But the lowest connection interval I could get were 30ms.
Anyone has experience to achieve the connection...
Hi.
I find this code github.com/.../nrf51-dfu-single-bank-ble
I want to compile bootloader and download it on PCA10004.
I have KEIL 5.12 and the project file of the link...
Hi,
I want to create a service for test logger. Through this service i want to write n bytes at a time and after few delay want to write again some n bytes. These written...
I'm struggling to get started using Keil with an NRF51822 mounted on a custom board that I have cobbled together.
I have opened the blinky/pca10031 example as a starting...
Hello, I have two nRF24L01 devices that can already talk to each other on a custom address. When I try to talk to the nRF51822 from one of the nRF24L01 devices, I cannot get...
services.h
Hi,
I'm writing an interface for my nRF8001 and am a bit confused about the NB_SETUP_MESSAGES value. In my services.h file the value is 14 when it appears there...
May be i haven't seen it, but how i can select if the setup will be stored in the NVM or volatile storage.
I prefere to start development with volatile storage.
On Page...
Dear All,
I used the array defined in services_lock.h to setup the nrf8001 module. Therefore, the service setup is written to the OTP memory in the chip. Now, I want to change...
Hi
I tried to connect our non-bonding device to Windows 8.1, but it ends in an error message. The implementaion uses the device_manager_peripherial from SDK 6.1 with the...
I am using the nRF8001 and trying to do ANCS. After rebooting the Arduino / BLE Shield, I have to reset Bluetooth in iOS in order for ANCS to work again.
I was thinking...
This is the second part of the problem firstly exposed in this question .
I have the problem that, with a Blend Micro Arduino board from Red Bear Lab after a while (randomly...
Hi,
I want to implement BLE based access control application. I have developed nRF51822 based Peripheral device & iOS application based central device to pair with the...
