Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi guys
I use gazell protocol for my application. I want to try some other way to decide the channel tables. So I decided to monitor the RSSI and chose the channels in...
Hello, I want to be able to perform actions in my app based on the tactile buttons being pressed on the beacon. When I bought it I was under the impression that the service...
Hi,
I have some problems to advertise a custom 128bit UUID.
I succeeded to set the 128bit base UUID and my Characteristics UUIDs are 128bits.
But how I can set the PrimaryService...
Hello,
I want to implement device pairing, using the pairing bit. The pairing bit is set in the masters device type. For a slave to pair with such master, it opens a channel...
Hi Nordic!
I am using nRF UART2.0 and nRF51822.
I am sending some data from nRF51822 to nRF UART2.0
But after 3 minutes, I can get disconnection.
and 0x16 error...
I am currently using ARM's CMSIS-DAP interface to support flashing of an nRF51422 from a host MCU (i.e. to perform updates of the SoftDevice and/or application code running...
Hi guys,
I have a custom hardware with the nrf51822 and we have a slow connection and services discovery is clearly slower that when we run the code in the Development...
I use two nRF24LE1s as transmiter and receiver Here are my questions:
I set the transmiter side to auto reply mode using PIPE0 ,but i found the STATUS regesitor to...
Hi I am trying coding a remote controller using nrf24le1 but failed. any sample code?
it with several keys when push down the pin will connect to GND.
when any key push...
Hi all,
I would connect the NRF8001 module to my microcontroller (SAM3SD8C). Does anyone have an example code for this microcontroller?
Otherwise is possible to modify...
Hi All,
We have a PCA10001 running a ble_app_hid_mouse (modified according to our use case) which receives data from PC UART.
We are trying to connect to this device...
I cannot find any instructions on how to "pair" the nRF8001 with a laptop (I understand that BLE doesn't pair like usual BT).
Are there any tutorials available?!
Thank...
I am trying learn how to handle a central when the bond has been deleted on the device only.
It is a HID device using softdevice7 / sdk6.1, with max 1 bonded centrals....
Hi
I've been able to include Device Manager to bond my peripheral to Master Control Panel, but testing with LightBlue runnining on an iOS 8 iPadI'm having several weird...
