Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi there!
I use RedBearLabs Nano (nRF51822) for at setup where I've developed BLE code in Arduino to communicate with apps on both iOS and Android.
Now I need to ensure...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
I am using this mbed workthrough, to create a custom GATT Service in C++. However, this code only creates characteristics with UUIDs:
uint16_t percentageUUID = 0xA002;...
This thread mentions having the master read the DFU Revision Characteristic to determine the DFU revision. I've based my DFU and application off the dfu_dual_bank_ble_310_pca10028...
Could you estimate the free space for Application on nRF51 and mRF52, on this case for Homekit with FOTA :
Boot Loadeer with FOTA
Homekit Enable
BLE Software Device...
What are the options to update firmware (Application/Bootloader/Softdevices) for multiple devices built on NRF51x22 ?
Using Master Control Panel could take days programming...
Dear Nordic Team,
I am using HID mouse example code in my nordic dk board.
I can able implemented fallowing logic in my code to do left , right and middle button click...
Hi,
I am using nRF51422 with SDK 9.0 and SoftDevice130 with nus service. I have a custom android app running on BLE uart service. Data communication and connection handling...
How to save the uart app on my nrf51dk board? it only runs when i connect it with the usb. another question nrf51dk have a nrf51822 chip(SoC)?
please help me out. i want...
Hi,
I have installed EmBlocks 3.2 (the last one) but only extremely simple examples will compile.
It appears that the support files in wizard/arm/nordic/nordic.zip/Common...
I have been struggling with the custom characteristic implementation. I have followed the great tutorial on custom service that is online but there is really no doc or information...
The nRF Beacons iPhone or Android app requires adding a new beacon devices in order to notified events. Is it a must for beacons? Or is it just a one step for examples. In...
I try to advertise with a custom UUID and I do not know how to do it.
The standard services works with 16 bits and I need to work with 128 bits
So how can I do it?
Thanks...
Dear Nordic family,
I am using Bluetooth Low Energy, Beacon module with ARM Core from Tindie ( Product link ). The reference manual from their website is attached IMM-NRF51822_RefMan...
I am trying to work on ble_app_uart example project working.
I am able to see that the "nus_data_handler" is triggered when any data is received over the BLE channel. On...
