Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I have modified the Android Blinky App to connect two peripherals (nRF52 DK)
Scanning and Connecting to two peripherals works.. but when i want to start sending notifications...
Hi, all.
I want read mouse cursor coordinates from connected target(PC or iPhone and so on) through HID.
And then, i want to align the mouse cursor in the target center...
Hi.
I tried "Go to definition Of 'sd_softdevice_enable",and
"Go to Reference To 'sd_softdevice_enable" at ble_app_hrs_c at ble_central,example .
But sd_softdevice_enable...
Dear all.
Now we migration from SDK 10 to SDK 11. but, there is not SDK11 packs. As you know, no pack is very uncomfortable for package managing on keil. please answer...
Hi,
I am using nrf52-DK (First Version in the moment) and need to test UART interface.
I use the example from the blue-nus example from the SDK which is working fine....
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi There,
How can I create a combined soft device and bootloader image/zip using the nrfutil.exe?
Is it possible to have an image/zip with both the application, bootloader...
Hello everyone,
I'm having trouble with nrfutil (python version from github.com/.../pc-nrfutil) . Here is the command line I use:
$ nrfutil dfu genpkg --application...
Hello, I use nrf51822 for my project. I have to collect data via BLE nus from phone, and then some time I need use a GPIO to simulate 7816 protocol, in that time I need 1...
Hi All,
I need to design mesh network using nrf51822, i referred so many posts in forum, i am thinking Mesh network not yet implemented!!!!!!!!!!!!! (i am not sure). If...
NFC samples in latest SDK 11 are working well when using Keil IDE. But there is no correct functionality with IAR. Samples compile well, code can be flashed and runs. But...
Hi
I want to calculate the estimated current consumption referring to nordic documentation .. In fact i can't pick how much time each stage ( A, B, C, ...) dures.
Any...
Hi,
Please share nRF51822 observer mode power consumption profile plot to get complete power consumption during only receiving mode.
See below plot for advertising mode...