Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Since related topic Is BLE changing licensing policy? was marked as resolved I moved my question to new one.
My company is ready to get SIG membership for BLE usage and pay...
I'm creating a custom beacon, similar to iBeacon, but with a custom data format. It advertises only once every 8 seconds, but the iPhone app doesn't receive advertisements...
I tried to read out the temperature sensor of NRF51822. In light CPU load (turn on ADC and send data through BLE every 1s), the measured value is around 45 degC, compared...
I am using the RTC1 compare event to generate a periodic interrupt. When I halt the bugger and and then run the interrupt doesn't occur. Looking at the RTC1 register set shows...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am working on a system where two nRF51 will communicate with use of the ANT protocol (S210). The master and slave must be paired after pressing a button on both sides. I...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I want to power the dongle from a 5V battery but don't want to solder directly to USB pads at the risk of ruining them. Can I put the 5V from the battery at the Vin point...
I have S110 peripheral device with custom UUID, created as described in www.nordicsemi.com/.../80193304 .
On the other side i have S130 device who successfuly scans and connects...
Sorry for the non-tech. question but I just heard that BlueTooth group is significantly changing BLE licensing policy. Maybe it's some kind of FUD but it should be mandatory...
Hello,
I am running the s110_nrf51822_7.0.0_softdevice.hex and am encountering an nrf callback assert on line 1377 of rem.c.
Without any visibility into this code I...
Hello, before you say anything: "yes I have searched!" :D
I found that this question was similar to mine
How to write GPIOTE Interrupt
Now I am fairly certain that I...
Hello,
I am trying to connect to one specific device. To make this I am advertising with the whitelist. The problem is that the whitelist do not seem to work. I got the...
