Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi:
I use the demo code (nRF51_SDK_9.0.0_2e23562-NORDIC\nRF51_SDK_9.0.0_2e23562\examples\peripheral\spi_master) find a BUG(?) : when i use 1M clock , 1byte translate use...
Hello,
I am currently optimizing the throughput for my mesh network and I am wondering whether I've hit the limit of what's currently possible. I have two methods for sending...
I want to measure the RSSI strength of my Bluetooth module, in various distances and situations.
I read in the description of the app nRF Master Control Panel that:
...
I'm trying to change the mac address of my nRF51822 chip using something like:
ble_gap_addr_t m_address_1;
m_address_1.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE;...
Hi,
I use GCC for compilation and nrfjprog for flashing. A few weeks ago I needed to switch on compiler optimization (Level 1) because my code grew a little too big. Now...
Hi,
I would like to have several nRF51 development cards connected to my computer at the same time using the USB debug port. The serial port and the RTT port work when several...
Hi,
We are trying to develop application with OTA DFU on nRF51. And we need to build bootloader ourselves. We use gcc for development. We found the bootloader example for...
I tried to run beacon example (from SDK 9.0). Even after uploading hex file I was not able to "see" becon. I'm using st-link v2 and openocd. Let me tell a bit more about what...
Hi,
I'm making device with nrf51822 chip and 400mA battery.
It connects to smart phone.
It has to calculate heart rate and some other things, so it's doing it on device...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
