HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
Hi I have built a custom NRF8001 board and I'm debugging a problem.
The main microcontroller works fine (atmega32u4) but the RDYN line never goes low to start the setup...
I am starting development on the nRF51422. I noticed that for the non-ANT sample code (blinky and UART), a gcc makefile and windows batch files are provided for compilation...
Hi,
Does the heart rate demo in SDK v4.4.0 work with SD v6.0.0? I'm using the QFAAC0 revision of the NRF51822. The demo works fine with SD v5.2.0. Is there anything special...
So far I haven't run across any code examples that will switch the BLE (S110) stack in and out. I'm looking to test enabling and disabling of the softdevice to see how that...
I'm reading AD-converter data usin nRF51822 SPI-Master. BLE-stack is active so I can't use
interrupts with SPI. I get data every 2 ms. Sometimes Events are delayed so long...
Hi,
We would like to implement a scenario that need two BLE devices,
One is Peripheral that able to broadcast and connectable,
another one is Central that able to scanning...
Hi,
I'm using nRF51 SDK v 5.1.0 with SoftDevice v6.0.0 on nRF51822.
I'm using the pstorage SDK module for flash operations.
I've found an issue with this module,...
Hi
In the product specification the S120 softdevice it is mentioned, that the S120 will support central and broadcaster role at the same time. This is exactly what we need...
