Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello,
Setup:
SDK 9.0
SD 8.0.0
I have an application where we are using Pstorage to store persistent system settings.
When I flashed the device we were using this...
Dear All,
I'm a beginner in programming of Nordic component.
I try to synchronise the date and the time between client which is an application in PC and a component...
I'm currently developing a concurrent central/peripheral application using the nRF51, S130 and SDK 9.0.0. It uses the Nordic UART Service, and it would be nice to make use...
Hello,
Is it possible to use EasyDMA directly with nRF52 SDK without using one of the higher level libraries that use it, i.e SPI / UART? I am interested in implementing...
Hi:
I want to let link manager controllby by me. for example, I want to ask link manager to emit such LMP_test_control, LMP_activate command via HCI. how to do by nRF51?...
Hi:
for nRF51
I want to send command to link manager by HCI command ,or example LMP_test_control, LMP_Activate , etc. Could I modify firmware to do it ?
thanks;
All...
Hello,
I have an issue that I can't seem to sort out involving the PWM module. I am currently using SDK9.0 and SoftDevice S110 V8.0 and I am using the stock PWM files from...
I have a nRF51DK. And I would like to be able, to enable/disable the softdevice with 2 buttons.
Button 1 on nRF51DK --> Enable Softdevice
Button 2 on nRF51DK --> Disable...
Hello,
I am working on nRF51822 S110 softdevice 8.0 and SDK9.0. I am creating paired and unpaired states and the system will goto unpaired only if it is unpaired from the...
I know nrf51 timer0 can be configured for 16,8,24 and 32 bit modes
and timer1 and timer2 can be configured for 16 and 8 bit modes.
But what can I expect the value to be...
I'm going to star a new product development using nRF51422 supplied by a 3V battery. Since it is a low cost product the idea is to use the nRF51422 internal DCDC to provide...
Hello,
I'm using an external chip that decodes my RF transmission and outputs the data on two pins DAT, and CLK (data and clock). Currently I'm reading the data with GPIOTE...
We have written our own softdevice, but now we have a question about the stack pointer.
I read in the softdevice specification that the nordic softdevices share the stack...
I have been trying to establish a link that will feed sensor data into my com port via a Bluetooth uart bridge. I got my closest today by doing the following.
Load SDK10...
