Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
Hei,
We would be using nrf52 chip in a very miniature device that should have both BLE and NFC capability. NFC is needed for just as a tag. Thus, nrf52 is a good option....
I moved from SDK 7 to SDK 9. I'm using timers with SDK7
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE, true);
err_code = app_timer_create...
I work with the IAR Workbench and the nRF52 and would like to enable the floating point unit. After installation of the MDK-8.1.0 and the check of the nrf52832_xxaa.i79 file...
Not able to access the corresponding On characteristic if having more than 1 service having this.
Noticed that the app always write to the last On characteristic instance...
I donwloaded and executed the nrf52 examples with Keil µVision as I use it everyday.
The problem is when I compile and use a BLE example, it is stuck in SVC handler.
The...
I have a problem to make a program that read e put a string in UART. In version 7 of sdk there are functions simple_uart_get() and simple_uart_putstring, but this functions...
In the examples\bsp\bsp.h file there is a typo on line 61:
#define BSP_APP_APP_TIMERS_NUMBER 0
It should be:
#define BSP_LED_APP_TIMERS_NUMBER 0
Where is the...
I'm building out a project in Keil using the latest SDK (9.0) and the S130 Soft Device, and during build, Keil complains in mem_manager.c that sdk_config.h isn't there:
...
