Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
As explained in devzone.nordicsemi.com/.../ I want to interface my Beacon to a Invensense sensor with I2C. I'm having a hard time about using the I2C drivers/examples...
i failed to program the ptr5518 module with a jlink EDU.
it gives me :
$ JLinkExe
SEGGER J-Link Commander V5.02 ('?' for help)
Compiled Aug 28 2015 19:48:33
DLL...
I'm following the SDK 8.1 example from here with S210 v4 but I never seem to get a PSTORAGE_STORE_OP_CODE or PSTORAGE_UPDATE_OP_CODE.
I do however get the PSTORAGE_LOAD_OP_CODE...
Hello!
I'll start by giving some context: custom bootloader created via modifications to the one provided in SDK6.1, then ported to SDK9.0. SD revision 0x0064, running...
I am working on an mbed nrf51-DK powered Bluetooth Low Energy project. I have been developing various GATT services, however, I have now found my project has got "stuck" on...
Hi,
I'm using 3rd Generation of the nRF51822 with SoftDevice 8.0.0 and SDK 10.0.
There is an example in the SDK installation folder which shows how to use the TWI transaction...
Hello,
I have PCA10004 rev 2.2.0 evaluation kit and have tested S110 applications with SDK9.0 and softdevice 8.0.
Now I am working on S130 stack, softdevice v 1.0.0 and...
Hello,
I am working on S130 stack with version 1.0.0 and SDK 9.0 . I am testing the example of ble_app_hrs_rscs_relay_s1 project and it is working as a peripheral but the...
Hi nRF team,
I read somewhere that the sensitivity of the nRF52 is degraded when the internal DCDC is enabled. Can you confirm or dismiss this? If true, what is the sensitivity...
Hi,
I want to use nRF52832 for our new development.
So I have to get examples source code like nRF51822's Keil Pack Installer.
Where Can I get example source code for...
I saw the video of csr mesh network. I want to try something like that using nrf51822. I have read the documentation provided in the link link
. But I only got a rough idea...
Hi,
I am looking for an wearable solution which should be able to full duplex audio transfer over Bluetooth. Is this possible with BLE 4.1/4.2. As here battery life is...
Greetings. Could you provide more information on the issues with GPIO located near the radio in the nRF52 (PS 18.2.1)? Specifically, what is considered "high frequency digital...
