Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I'm implementing a simple bootloader which will not use BLE.
Application will transfer the data from mobile devices using BLE and this data will be stored to...
I'm looking for a smart solution to connect my application to different ANT+ sensors and transmit a logfile to a mobilephone via BT (and receive notifications from mobile...
Hi~ Sir:
I test S120 connect with S110 have problem ,test methods are as follows
S120 connect with S110 ,function ok.
S110 Power Off and On, the interval time about...
Hello everybody,
I've been digging through the forum and the documentation for hours now. But to be honest I don't understand the whole timer thing.
I need a simple...
Hello,
while implementing a BLE link layer, I’ve stumbled over a race condition, where I have a problem to find the cause. Maybe someone of you have an idea, on how to...
I am reading data over the duration of 3 seconds on SPI, but while I'm doing that, I need to send that data over RF using microESB library.
I need to make sure the read...
I use the chip nrf51822, However, SDK8.1.0 example ble_app_uart is base on nrf51422, what I need to do? just replace bsp.c ? and which bsp.c file corresponds to the nrf51822...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
I cannot program an external nRF51822 module(program old softdevice S110 6.0.0) with nRF51-DK p20 (SWD), it give message "invalid parameter error".
and i program the 51422DK...
Hi all,
I want accive this situation. My peripheral connecting a central with a service for example hrs, then i stop the conect with the function sd_ble_gap_disconnect(m_conn_handle_peripheral...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
I am using nrf51822 qfaa IC (pca10004 board) with softdevice v8 and sdk9. Now I am trying to do the dfu example. I uploaded the softdevice with the help of nrf gostudio. But...
Hi,
Please correct me if I'm wrong.
Consider an application that will read 6 bytes of data from I2C at 200Hz (each 5mSec) and will stop after 2000 reads. This will be...
Hi,
Apologies if this is an obvious question, but I haven't been able to establish from previous questions or the data sheet whether it is necessary to use an external...
I'd like to be able to change the connection interval from my central device on the fly after a BLE connection has been established between it and the peripheral. What's the...
