Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hi Nordic!
Long time short, I want to do an ANT application (S210, nRF51422) that pairs two slaves to one master. I have configured everything such that it pairs only when...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi Nordic,
We are trying to supply the chip nRF51422 with a Li-Ion battery. The nominal voltage is 3.7V, but as it is known, when full, this voltage can reach up to 4.2V...
Can the pc_ble_driver project located here be use in combination with SDK12?
We currently have it setup for SDK11 here, and want to upgrade to SDK12. We successfully built...
I want to develop a central role application (using a Redbear BLE Nano - based on nRF51)
I believe that this requires use of a softdevice and am looking for how to do this...
Hi. I am trying to set up timer in counter mode to count up signals from gpio through the ppi module, but it's not working. In main cycle I am testing the timer using led...
I want to sense bluetooth from any distance the radio can detect and without connecting, pairing or bonding. Simply turn led2 on while the nrf51822 senses RF and when it no...
For my application I need a lot of different timers. I dont use a soft device. Its a nRF52 Chip on board.
#define APP_TIMER_OP_QUEUE_SIZE 20
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Experimental Buttonless DFU worked correctly when compiled with keil, but the same example compiled in eclipse by gcc is not switching to bootloader mode. value 0x01 is updated...
Hi There,
Are timers 3 & 4 accessible to the application when using the v3.0 S132 softstack on the NRF52?
Looking at table 4 of S132_SDS_v3.0.pdf they are not listed.
Cheers...
Hi Community, many thanks for reading!
I have built a Breadboardadapter for an ISP1302
Inside
On Breadboard
There is no Groundplane or design rules.
Yes,...
I am using a nrf8001 and the arduino aci library ported to work with my project.
I have started from hello world example.
Connecting to the device from android app, sending...
Hi there.
I am compiling the Nordic MQTT subscriber example (using TLS), and see the following error:
c:\program files (x86)\gnu tools arm embedded\5.4 2016q2\arm...
I have an example app ble_app_cscs_pca10028_s110 and when I add /../../../components/drivers_nrf/nrf_soc_nosd to User Include Directories I get an error NRF_EVT_FLASH_OPERATION_SUCCESS...
