I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Hello
I'm currently trying to connect to an AWS IoT Core broker using the MQTTX client. I'm generating the necessary certificates through the CreateTeamDevice API endpoint...
As the poster above mentioned, the nRF54L15 ENGA version is stuck when initializing the GRTC.
it gets stuck at nrfy_grtc_sys_counter_start().
The SDK is 3.0.2.
Is there...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi we are using NRF51822 board.
i flash ble_app_hrs application. then it is giving advertisement.
but when i call twi_master_init() function from main. advertisement...
szenario
beacon and receiving nodes are all MCU based and all powered by net, no local battery needed
the beacon usually located near the floor, the nodes will be located...
Blicky project runs and I can set break points and run through them - watching the LEDs blink appropriately. However, the HRS and Proximity projects will successfully load...
Hi all,
I'm using the LE1 to do the mutilceiver,if I donn't use the dynamic payload,I can do it successfully.However,if I use the dynamic payload to do Multiceiver,the...
Hi,
For the LE1,I found that 32.768kHz crystal oscillator need long time(about 350ms) to running,I must do some delay(about 350ms) for the software then use the RTC,or...
In moving to the "rev-2 51422 silicon, we find that the app_timer inevitably fails after minutes to several hours. Power requirement moves from about .002ma to 4.5ma then...
Hi,
I am planning to use an external DCDC to supply the NRF51822 in Low Voltage Mode.
In the datasheet a voltage range of 1.75-1.95 on VDD and VDD1.8 is mentioned. ...
Dear all
I'm testing for RF stability. As i used 24LU1(host) with 51822(device) be the platform. For audio data transmission. 8k 8bits data rate.
Timeslot set as 1008us...
Hi,
I don't have any problems running the bootloader with S110 7.0.0.-3.alpha on the PCA1001 but when using the same code (minus the led and button config of the PCA1001...
Hi,
I am having a hard time with the permanent storage.
I got it to work with updating a 24 bytes long struct in a persistant block of 32 bytes.
I noticed that the...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hello Gentlemen,
I'm looking for a good example on how to pair BLE sensor and Android using static passkey. I looked at ble_app_gls but I could not see how they set the...
I have the following code
// bondmngr code comes here for now
ble_bondmngr_init_t bondInitData;
bondInitData.flash_page_num_bond = FLASH_PAGE_BOND;
bondInitData.flash_page_num_sys_attr...
I want to save data sent by the Nordic UART/Serial Port Emulation over BLE to the phone.
Can the Nordic UART app save received UART data sent over BLE to the phone?
