Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
hi,
In my device(nr51), have multi service and one client.
when i initial the client first ,then to setup service. this follow is O.K.
But, if i initial the service, and...
Keyboard source: Desktop 2 v1.0.5
Dongle source: 1. Desktop 2 v1.0.5 dongle hex; 2. Desktop 1.2.2.293 dongle hex
I found it is very defficult to pair the keyboard with...
Hi,
1. I have some puzzles,please give me some explanations,thank you!
In my design,I use some 51822 devices as tags which can communicate with the host.
The tags can send...
Hi, I want to know what's the differences between the NRF_CLOCK_LFCLKSRC_RC_250_PPM_xxMS_CALIBRATION and NRF_CLOCK_LFCLKSRC_XTAL_xx_PPM where xx means a decimal number.
when...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hi,
I want the NRF51 to respond to a received packet from a particular device using register TIFS to control the interfame timing.
For TIFS to work I have to set the...
Dear Nordic,
is it possible to build a simple data bridge at speed of 115200 and up based on nRF51822 with CTS/RTS support and a fixed pin code for nRF51822 pairing?
I am working on a multi-node network application with multiple transmitters and receivers and I have a question about timing for chips like the nRF24L01+. I would like to...
Hi
In my case i have gpio interrupt for every 25ms. so i change button detection delay t0 10ms.
and i given timeout in all while loops of twi_hw_master.c.
but my...
Hi,
we have nrf51822 custom hardware.
we are flashing application through j-link.
but after every flashing , i need to do switch off and on the device.
then only...
I have no power on my nrf6350 display
I programed the board with the display jostick example but cant see nothing on my lcd of the nrf6350
any advice?
thanks
...
Hi:
I'm fresh in use BLE.
when i installed SDK, i could not install the lastest version v4_4_1,but can install v3_0_0.
My system is MS win XP Pro SP3.
Please tell me what...
hi,
i took the same example of BLE_LBS, as it is working properly in case of writing to the device, but when i implemented my own for writing to the server, it is not working...
Hi,
I need to send more than 500 packets(each 20 bytes) to the master for every 1 minute, through the timeout handler. But i cannot able send all the packets, btle_connection_timeout...
