Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi devzone...
My setup is nrf51422 dk with soft-device S110 on the server side and on the client side i am running MCP 3.8.0 on a PC using usb dongle.
I am using Queued...
1 sensor per nRF51288.
Sensor supports either 400kHz I2C (10k pull up recommended) or SPI (2MHz typ, Max 20 MHz)
From the nRF51288 Product Specification:
Run current...
I want to use the s130 softdevice because we need the broadcaster/observer mode at the same time. I bought the nRF51 Dongle and the beacon Device.I use the Keil IDE, debugging...
From the question "Advertising on a single channel", the new S110 supports advertising on one single channel. What I want to know is if S120 supports listening on one single...
Hi,
Thank you for looking into this issue.
The target BLE module we are using is a custom board (Rigado BMD200) based on nRF51822 s110 chip. We have tried a few example...
Hi,
I am following the tutorial using Raspberry Pi Kernel version 3.18, but after the step 7, the raspberry gets frozen with the colorful image in the beginning of the boot...
Hello,
we want to establish a UART communication between the Dynastream N548M8CB Module and a TI Mikrocontroller. I have tested the UART loopback example with the pca10028...
In the data sheet of SHT21 is this the formula to calculate the temperature:
T = -46.85 + 175.72 * temp_data / 2^16
temp_data has the value 26'464.
The result should...
Hi,
I'm trying to define a new service, and on the GAP settings, I would like to advertise my service, but I get an error message: advertisement packet too long.
What...
I have a temperature/humidity sensor from Sensirion. The Type is SHT21x. The sensor has I2C so it should be able to tranfer the data from the sensor to the Nordic chip over...
Hi,
I am attempting to get the ble_app_beacon example working with the s130 softdevice instead of the s110. I am using armgcc and the v8 sdk softdevice headers on a pca10031...
Hello, I have inherited a project from a departed employee. I have a requirement (based on a stated desire from her to my project manager) to "bring the SDK and/or SoftDevice...
Hi,
I am using the nRF24L01+ evaluation kit in a project. Through the EV KIT software I am able to configure the nRF module in receiver mode. I can even see LED 2 light...
Hello,
I am trying to modify the ble_app_uart example from the S110 to the s310 softdevice. I am using the project from nRF51_SDK_8.0.0_5fc2c3a.
I modified the Paths...
Hi,
We are planning to design a custom based on nrf51822 with 1.8v power supply. we just want to know is there any restriction towards accessing peripherals on chip like...
