Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi
I've installed the new tools in version 7.5.1 to support the new nRF52 family. While working on the nRF51 again i found out, that the old parameters i used for programming...
Hi,
I'm working on a project where nrf51 modules should communicate with each other. For that i'd need to set characteristic that can store string. Now i've done that ...
Hi,all.i call function "sd_clock_hfclk_release(); power_manage();" and want my device to sleep.as this,my device's current is 2.2mA.what's wrong ?Can someone help me?
I have a master device using SPI interface , write data to nordic SPI salve and send data to cell pohone.
But ,the master device SPI wirte data is fast, the nordic will...
hi all,
since i am new to nRF24L01+ device, kindly any one provide me details regarding range that can be supported by nRF24L01+ device.i already try to find out information...
Hi,
I am attempting to create a secure BLE connection in security mode 1 and level 3.
I noticed that when I simply call sd_ble_gap_authenticate with MITM = 1 it seems...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off the radio while keeping just RTC timer on.
So, after shutting down...
Hi there,
When I tried to send data chunk (it's about 8K) to phone side according to this , the speed is much slower than 1K/s, and what's more, it's disconnected with...
Hi,
I have a problem in CRC of setup message for nRF8001,
and I already try the CCITT-16 algorithm with below conditions:
Poly = 0x1021,
Init = 0xFFFF,
Ignore all...
Hi,
I want do RSA on NRF51822. The build environment is GCC. And the develop base on S120. The RSA need 1K to do calculation. If I enable the RSA calculation, the APP may...
Is there any high-level documentation of the nRF52-DK (PCA10036) connections?
Studying the schematics, I have inferred some of the intents, like:
built-in JLink automatically...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
Hey,
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02...
Hi,
I am new to the nrf51 and I building a complex ANT application. I have part of the ANT application working but I would like to debug with printf() statements to find...
After testing with 5-6 different phones it is evident that there are major differences in how well BLE is actually supported. The Android/Iphone (and manufacturer SW) version...
