Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
Hi,
In my project, I need to periodically perform some jobs on the nRF51822 Beacon kit (sdk 7.1). For that, I think I need to use timers. However, I'm not sure how to do...
Hey everyone.,
I was trying to use nrf51822 as spi slave and just a heads up to know that i use Nrf51822 as master. I see that when chip select CS gets low SPI needs to acquire...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
Hi,
I'm trying to determine why a HCI DFU upload fails.
There is a log of the communication below showing the serial request/responses on the Windows side.
Is anyone...
Hi: I use dfu_single_bank_hci to update application. HCI_SLIP_UART_MODE = APP_UART_FLOW_CONTROL_DISABLED, HCI_SLIP_UART_BAUDRATE = 38400.
I use command " E:\hci_dfu_send_hex...
Hello,
In my quest of working with pstorage_raw.c I found an annoying situation when I tried to clear small portions (as I thought by using raw I would have full control...
