Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi guys,
I want to use the nRF51822 as a gateway to send uart-commands from the µC to my iPhone and vice versa.
µC---|uart|--->nRF51822 ) ) ) ) BLE ( ( ( ( iPhone
...
Hi,
I am using the NRF51822-CEAA flip chip package for my custom board.
Because this package has an optical vulnerability from the sides, could you please advise how...
Hi developers,
I recently had a problem with nRF51822 and radio interrupts.
My situatios is quite clear but I cannot resolve the problem. I hope You will help me.
Description...
hi,everyone.
because of careless,i enabled pin reset in debug mode by set bit 0 in RESET register in my software,and i downloaded the hex file to a 51822.now,because of resetting...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
I'm using the TWI module. Where can I set whether the DSA SCL pins have the internal pull-up enabled or disabled? I can't even find where to see if they are enabled at all...
Hi guys,
I am having a breakout board made and would like to know what are the programmers out there which I can buy which will help me program the board. The J-Link is...
Hi,
I'm designing a custom board equipped with nrf51822 and is not clear for me how the flashing part works; I bought nrf6700 and pca10005 as reference design and now i need...
I am coming across a strange issue with a nRF24L01P running enhanced shockburst. I have 1 PRX and a few PTXs communicating in a star network. The type of PTX determines which...
Here i am attaching text file in which my application not able to call interrupt handler.
Kindly tell me what will be issue.
Regards
Balaji
rtc1_app_timer.txt
I'm trying to figure where the BLE bottlenecks are to figure if I should use BLE or maybe Gazell for my product. I've just started to use the BLE stack, so I guess that there...