Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello all,
I currently have a test rig with 3 sensors, each with their own pin and interrupt they are supposed to carry out. Whichever two I put first in my gpiote_init...
Dear all,
I'm using SDk130 and the Software is based on the ble_app_uart_c example.
Now I want to scan the advertising data from a peripheral (device name, peer address...
Hi all,
Will the Gazell protocol be available on the nRF52, or should I stick to an nRF51?
Also for a new product, is it better to use Gazell than ESB?
Thanks!
I am new to android studio. I downloaded git hup zip folder and also dfu folder. I unziped both in a same folder.
I opened the extracted folder using android studio. But...
Am using NRF52,S132 softdevice
devzone.nordicsemi.com/.../
I took the answer by Ole in the above question as my reference . According to this once I stop advertising...
It is good practice to prefix all functions from a C library with a prefix, to avoid collisions with other libraries that the end-user may link with. Unfortunately the Nordic...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hello,
I need to read by Battery Voltage using ADC. My Battery is 3.3v which is being stepped down to 2.1V using a LDO regulator. So my VDD is 2.1V in DC/DC mode.
Now I...
Hi guys I'm sending data from an nexys 4 fpga through an spi to my nRF51 (pca10028) I have the fpga set as the master and I'm able to read data sent to the nRF51 through my...
Hi.
I'm using nrf52 as slave for another device. I'm reading test string from the nrf buffer and I can see extra zero (rest of the content is then offset by one -> corruption...
Hi, i know this question has been ask before but, i was reading and readind and i could find a way to do it. I got the theory but when i'm going to implement it in my code...
Hi there,
i cannot get the hrs_c example to connect to a heartbelt.
The heart belt is found and a connection is established:
[APPL]: >> DM_EVT_DISCONNECTION
[APPL...
Hi
I am working on nrf52 using BMD300 RIGADO board.I am trying to run BLE UART example of nrf SDK 11.0.0.But while I am running the code I am getting errors as
: struct...
