I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hi,
I'm working on a custom board based on nRF52840 and a 2.9" ePaper display (SSD1680) connected via SPI using the mipi-dbi-spi interface. I'm using nRF Connect SDK v3...
I am trying to create a custom sensor for CT1711 temperature sensor. I have created the sensor driver code and device tree binding, but it won't start (initialize) and the...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Hello, I am designing a PCB with nRF51822 and I would like to know which is the best option to add battery charging to my PCB.
I think the most common options are these...
Dear All,
uVision debugger seems to execute code randomly. Picture shows stepping through the code. Codeline marking in grey also seems odd.
I would have expected to...
Hi,
I suffer from the phenomenon which can't sometimes maintain communication between the 32.8ms at Gazell communication at present.
When not writing in SoftDevice, this...
Hi,
I am using " BLE-Gateway " example from nRF51-ble-bcast-mesh to advertise my custom "Manufacturer Data" from 1 nRF51422 device to another nRF51422.
I've made the...
I have been able to implement the PER test (on nRF51822) using the direct_test_mode_s110 and code based off the example python code from the nAN34 zip file. I adjusted to...
Hi,
I want write a demon running on linux to control the 51822 dongle to connect or disconnect with mobile phones.
Now I have one idea, which is using string as command...
Hello,
I need to send packets that are larger than 20 bytes to once characteristic with a variable length. When I set the variable length to 100 bytes, the Attribute table...
NRF51822 supply voltage is 3V battery. When I design principle diagram, I have a question.
Both AVDD and VCC_nRF are connect with the battery's positive?
While trying to get the SDK's bootloader working with gcc, I have to replace some ARMCC-speific code found in bootloader_util_arm.c:
__asm void StartApplication(uint32_t...
I am using the nRF51-DK and have Timer1 setup as follows:
void start_timer(void)
{
NRF_TIMER1->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1...
Hi Guys,
I am currently using the ble driver for windows (Python) to get notifications from two Gatt services (Same Service/charac/descriptors/etc basically same application...
I've just trying to get SPI working, everything is compiling OK but when initialising the SPI, when the line below is hit,
/* Clear waiting interrupts and events */
p_spi_instance...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
I would like to support app_button, however I need to configure a pin as NOPULL and trigger on a low to high transition without debouncing.
I don't see a way this can co...
