Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\ nrf52-ble-tutorial-service.uvprojx, and compile ,the result...
Hello,
I am developing custom driver for TWIM. I am facing a problem with DNACK and ANACK which hangs my application. SCL and SDA lines are monitored through Saleale logic...
hello,
again, sorry for the begginers qustion(probablly i will have 2-3(hopefully) in the next few days). I got today the nrf52-dk, and on the back of the nrf52 is written...
I ask the questition yesterday ,maybe i have not expressed clearly.In my project , I have to use three spi in master mode and three twi in master mode to communicate with...
Hi!
In my teamwork we are developing an application for use a sensor module via spi, and share data and comunicate with other devices via Bluetooth.
I've taken care...
Dears,
We are working for a dongle solution to exchange data.
Have any BLE SDK solution via Uart to exchange data between host & client? and that the host is no need...
Hi,
I am using nRF51822xxaa and s130 and SDK 10.0. nRF51 connects with the app(notifications enabled), then bonds with it. Subsequent communications between the app and the...
I connected with RTT Viewer 5.12f with nrf51 DK board.
while I donwload firmware to the board, I got bunch of error message from RTT viewer..and it stop..sometime the download...
I am having two issues with the following code:
When I run this sample code on my NRF52DK (there's external hardware connceted but that does not affect this operation...
Hello, everyone~
I used to see nRF51802 in an official document but cannot find it in the official website. Is there an nRF51802? If so, what are the differences between...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
Hello everyone.Recently I try to send some information from a "nrf51822" to phone when they are connected .So I choose "ble_app_hrs" example program,and I add two characteristics...
