Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Is it possible to use PPI and RTC to turn the HFCLK on or off ? (external Xtal)
Example - something like this ...
NRF_PPI->CH[9].EEP = (uint32_t) &NRF_RTC0->EVENTS_COMPARE...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
Hi,
I'm writing a service to send indications on a couple of characteristics that are part of a service. In order to determine whether indications have been enabled or not...
Hi,
Is there a smaller version of the desktop 2 firmware? I don not need firmware for NFC only ble 4.0. Also would like less complicated pairing. The 6 didgit code is unnecessary...
Hi , I tried to change the transmission power using the s110 API and tried checking if the value of the register storing the transmission power is changed or not. Following...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
