Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi all,
I want to add 128bit base uuid for each of my three service,but there is a problem ,I add different base uuid for different service ,but I can only see one base...
Hello,
Please be gentle. This is my first time;) .
I am a retired computer/medical electronics/electromechanical device field engineer.
A friend got me interested...
in sdk 4.3, I used two different ways to know it is read first time(in factory)
NRF_ERROR_NOT_FOUND from ble_flash_page_read to indicated first time it reads
0xff...
I have 3 questions:
1. How to set device to non-discovery mode?
2. Once the device is in non-discovery mode, How can host connect to it?
3. Can I use Master Control Panel...
Hi sir
On your Beacon kit, we found it was used external 32.768KHz at 20ppm.
Question is on iBeacon usage, is a external higher precision 32.768K crystal necessary ? ...
Hello,
I'm working on an ultra low consumption purposes with which NRF51822 commnunique in BT4 with softdevice version 5.2.1.
I compile with GCC 4.7 2013q1. Unfortunately...
Hi
I've have customized a state machine and output patterns for the nrf8002 using the development kit. Now i have my own pcb design and I'm aiming to build a small prototype...
I installed master control panel and plug a PCA10000(usb dongle). The panel discovered the dongle.But once i press "start", an error hanppend:
"ascii" codec can't decode...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi there,
Im wondering if its possible to implement a proximity monitor with the new s120. Having one nrf51822 acting as a central and several (up to 8 I guess) nrf51822...
Hello,
at my current project I send a lot of data from one evalboard to another via proprietary Software.
Now I want to send that data via Bluetooth LE from one evalboard...
I would like to confirm the availability of the nrf51822 with DC/DC.
Should the nrf51822 with DC/DC be used in new designs? Will it continued to be available in 2015 and...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
