Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
I have a custom board using a nRF52840.
A part of the configuration is a Analog Devices MAX98357AEWL+T Class D amplifier which is driven by i2s0.
When the board is idle...
I want to bring up my own new board, but the nRFStudio can not connect to the J-Link, please check the picture.
I connect 4 lines from board to J-Link, including VCC, GND...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I haven't seen any posts about this, so I thought I'd post what I observed and how I fixed it in the hope this helps someone else.
My nRF51 DK (PCA10028 v1.1.0) out of...
I have gone through most of the guides/links that I saw here to no end.
My development environment is OS X 10.9, gcc-arm 4.9, nRF51822 beacon.
Before going for the IDE...
Hi,
I am trying to build a low power device using the nRF51422 SoC without a Soft Device. I need a timer to occasionally wake up the chip and as I read the product specification...
I have a basic question regarding a basic area. Interrupts! But without any good specification and how the OS work and good example how to do this I need to push for the obvious...
In ble_dfu.c (unmodified SDK 8.0.0) I am unable to get the buttonless DFU hooked up.
For reference, ble_app_hrs with s110_with_dfu works correctly. I have traced my issue...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
I am searching a cheap wifi solution and this NRF24L01 communicates through 2.4GHz network, therefore it may be compatible with 802.11 protocol and further with TCP/IP protocol...
Hello!
We're using PPI to connect one pin to clear and capture events on Timer2. On pin low-to-high we're clearing the timer and on pin high-to-low, we're capturing the...
Hi,
I am planning to use nRF51822 for one of our projects.
Can you please hlep me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards,
Sumit
Hi,
For SDK 8.0.0 and Softdevice S120.
(1) Maximum number of services supported for db discovery ?
(2) Maximum number of characteristics per service for db discovery...
When i try to add pstorage in Keil 5 packs manager without a softdevice ble_flash is required as additional software component. Adding ble_flash requires a softdevice as additional...
