HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello,
Please be gentle. This is my first time;) .
I am a retired computer/medical electronics/electromechanical device field engineer.
A friend got me interested...
in sdk 4.3, I used two different ways to know it is read first time(in factory)
NRF_ERROR_NOT_FOUND from ble_flash_page_read to indicated first time it reads
0xff...
I have 3 questions:
1. How to set device to non-discovery mode?
2. Once the device is in non-discovery mode, How can host connect to it?
3. Can I use Master Control Panel...
Hi sir
On your Beacon kit, we found it was used external 32.768KHz at 20ppm.
Question is on iBeacon usage, is a external higher precision 32.768K crystal necessary ? ...
Hello,
I'm working on an ultra low consumption purposes with which NRF51822 commnunique in BT4 with softdevice version 5.2.1.
I compile with GCC 4.7 2013q1. Unfortunately...
Hi
I've have customized a state machine and output patterns for the nrf8002 using the development kit. Now i have my own pcb design and I'm aiming to build a small prototype...
I installed master control panel and plug a PCA10000(usb dongle). The panel discovered the dongle.But once i press "start", an error hanppend:
"ascii" codec can't decode...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi there,
Im wondering if its possible to implement a proximity monitor with the new s120. Having one nrf51822 acting as a central and several (up to 8 I guess) nrf51822...
Hello,
at my current project I send a lot of data from one evalboard to another via proprietary Software.
Now I want to send that data via Bluetooth LE from one evalboard...
I would like to confirm the availability of the nrf51822 with DC/DC.
Should the nrf51822 with DC/DC be used in new designs? Will it continued to be available in 2015 and...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
