I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
I've recently been playing around with Bluetooth Developer Studio, and I can see it's potential despite it having a few annoying bugs.
I've set up a custom service by re...
Where would be a good place to feed a watchdog when using a softdevice?
My first guess was in main loop:
for (;;) {
NRF_WDT->RR[RR_number] = 0x6E524635;
power_manage...
Hi,
When a watch dog timeout occurs, I want to save some data to the flash memory prior to reset (namely the RTC count value). Therefore I enabled the wdt interrupt. The...
Im using nrf51, I configured the watchdog to reset after 3 seconds of hang and it works. But I have absolutely to save some data in flash before reset
Is there anyway to...
My custom profile was being built fine until I added a couple of standard descriptors to a custom service characteristic. Any idea what's going on here?
19:34 - [Code Generator...
Hello All,
I want to develop bluetooth mesh using NRF51.
I have question about this:
Is their library closed or not?
Do we need smartphone like in CSR?
...
Hi, I have a TinyShield Nordic module and I am having some troubles trying to customize the advertising packet. I have downloaded NRFGO Studio and I have enabled service data...
I have an nRF 52 dev kit, an Asus router running openWRT, and an android phone with the master control panel.
I'm able to compile and flash the dev kit with the example...
hello,
I am using the nrf51822, I want to add a normal service which do not need bond before used at the ancs example.I hope it can do the follow tow points,firstly,if the...
Hi,
I tried to figure out what is happening on the lower Bluetooth levels but it is very difficult to find straightforward information. Especially the Bluetooth (4.2) standard...
Hi, My apologies that this seems repeat information from previous posts, however they do not give a clear answer to my question regarding 4.2 compliance. I must also state...
Hi,
I want to count the time in seconds for which I press the button and stop the counter when the button is released. How should I detect the long press of button and...
Hello,
I need to use storage component with wear-leveling (i need to save some data persitant quite often). I decided to use Flash Data Storage (FDS).
I found fix for linker...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
nrf51822-QFAA has 16KB SRAM，when run with SoftDevice S110 v9.0.0,
the memory areas is below:
why the size is 0x2000(8K)?
when change size to 0x4000(16K), the app can...
