Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello! I want to broadcast messages between 2/3/4/5/... devices. How Can I broadcasts between devices? Each device must receive messages from others and also broadcasts to...
Hi,
I'm unable to configure the UART so, that it will generate the TXDRDY event. I have an UART that should send periodicaly 4 Byte sequences without hardware handshake...
Hi,
For my research project on novel antennas I need a demonstration prototype, and the nRF51822 Beacon Kit would be ideal for me (due to its small size and battery power...
Hi there,
I was wondering it it is possible to use MATLAB as a central device, using a third party dongle?
The MATLAB Instrumentation Contol Toolbox can be used to control...
Bluetooth v4.2 included an ability for attributes to be greater than 20 bytes of payload data long. Is there anything in the nrf51822 hardware that would prevent this from...
Hi,
Does anyone know the maximum baud rate of the nrf24l01+? I am trying to talk to it through SPI but observe that when I increase SPI speed I read incorrect values. Does...
Recently I was attempting to use the nrf51822 SDK's app_uart module's APP_UART_FLOW_CONTROL_LOW_POWER mode (currently using APP_UART_FLOW_CONTROL_ENABLED ). I noticed that...
Hello,
I would like to send some data i read over I2C. But the I2C and BLE Stack should not run at once, is it possible to check the state of the BLE stack?
The core specification v4.0 vol 3 part C section 3.2.2.3 "Bluetooth Device Name -- Representation" states that the device name can be up to 248 bytes. I've confirmed that...
Dears:
I know there are three modes as below :
(1) internal LDO regulator
(2) 1.8 V low voltage mode
(3) internal DC/DC converter
So, I have some questions as below...
Hi, we are trying to calculate operational current. Does anyone know what the test voltage is in nRF51422_PS v3.1. I assume for typical it's 3.0V and Max is 3.6V?
Also is...
I have a 256k NRF51822 with S110 installed.
I have a small custom bootloader that is located at 0x3f000.
I used nrfgo studio to install the S110 stack, then the bootloader...
Hi everyone !!
I have this hardware mapping, and I'd like to detect pin state change with an interrupt.
My problem is that it seems I can't configure an interruption...
