Hi, I have issue where the slot 1 image seems stuck. It can not be erased, confirmed, or swapped in the state that it is currently on. When I click erase, the error bad state...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
Hi Nordic team,
According to the Migration guide for nRF Connect SDK v3.0.0 for the nRF54H20 SoC, there are two required steps: loading the nRF54H20 BICR file and the nRF54H20...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
1. I am trying to implement DFU(with USB&BLE) and USB Mass Storage with FAT FS filesystems on external QSPI flash. I am getting the following build errors- with SDK version...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Dear Nordic
I am programming with nrf52833,ncs v2.9.0 base on sample\peripheral_hid_keyboards
Peripheral side(nrf 52833) adverting as Scanner_CE42,and iphone connect to...
I am developing a product using nrf51822 v5.2 SDK.The question is that Ble will automatically disconnect in some minutes after normal connect OK.The message by Sniffer is...
Recently while debugging my application i noticed strange behavior:
i set watchdog timer to restart application if my peripheral is not receiving any data for some time....
I have a nRF51822 Evaluation kit I am trying to get up and running. My kit has the older QFAACA part.
I followed the steps to setup eclipse and GCC and i am successfully...
Hello,
I took the ble_app_hrs rebuilt it and used Control to verify all is correct. I also tested it with the nRFTools Android App and it works fine I see temperature changing...
Hello,
I am currently starting with the hole ble topic. This forum helps me a lot in the last weeks to understand ble.
I am using S110 to provide a peripheral device...
I use the nRF51422 with S310 stack and i found the nRF51422 power consumption are quite different after connection on different phones which run the Master Control Panel as...
I have written some code that uses the SPIS to transmit data. One of the bursts is constant, for example I have a fixed sequence to send using the SPIS and so if I define...
Hello.
I use nrf51822 EK and custom board.
I have to replace the bd address i can not be found in the ble_app_ibeacon_bcs source code.
Is it any way to fix the bd address...
Hi. I'm curious if there's a way to filter devices in the "Discovered Devices" list while scanning with MCP. We have a lot of BLE devices in our office, so the list is fairly...
Hello, I am looking for the way I can use PWM to control duty cycle of connection. I am really novice and my understanding about programming and Bluetooth protocol is really...
I'd like to use the pin sense function as the power switch of my NRF51822 device. That is to say, after the very first power cycle (reset or battery change), the device goes...
Hi everyone,
I am trying to learn nrf51822 using Keil,
I need a very simple program to learn such as:
function bluetoothhandle(value)
{
if(value=="test1")
{
bluetooth_write...
Hi,
I tried to combine BLE HRS & UART together on nrf51822. The service initialization code is
void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;...
