We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
my dk board is nrf51422 and nrf 52382,
the central role is nrf51422, and the peripheral role is 52382.
my sdk version of 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I'm trying to get a module with an NFR24L01+ on board to send a simple data transmission from a pic micro but after a couple of days of trying various combinations without...
i find that the macro APP_ERROR_CHECK call the macro APP_ERROR_HANDLER
do \
{ \
const uint32_t LOCAL_ERR_CODE = (ERR_CODE); \
if (LOCAL_ERR_CODE != NRF_SUCCESS) \...
HI all:
Because the application code is relatively small, bootloader is used dual_bank_mode, but now the application code becomes large, OTA can not upgrade, I would like...
My PCA10001 board is getting detected in nRFgo studio and i can even program it but its COM port is not getting detected in device manager.
I dont know what happened but...
Hello Nordic--
We're most of the way through qualification testing on an nrf51822 and the testing house had a question about the PIXIT values for RF-PHY testing. I sent...
Hi,
I find three different states that is related to DFU and app_button libary.
1, no DFU(that is no bootloader), but using app_button libary, there is no 0.9mA current...
Hi. I use the 'sdk 6' and 's110_nrf51822_7.1.0_softdevice'.
I would like to add security.
I tried to passkey. If i enter passkey, it is possible to bond. but It is not...
Hi all,
I can control volume up/down, music play/pause with the ble_hids module.
static uint8_t report_map_data[] =
{
0x05, 0x0c, // Usage Page (consumer device)
0x09...
Hi.
I'm currently trying to buffer data from beacon interrupt.
So, I choose to use circular buffer.
Before implementing it myself, I could find that there's already...
Hi
I'm using the Adafruit LE Breakout with an MSP430.
I made my own drivers in order to have full ISR support.
My setup works well (no error) i can connect/set_local_data...
Hi,
I’m currently trying to send strings about Nordic UART Service.
In use are two nRF52832 Develop boards. One as Central and one as Peripheral.
The connection works fine...
I have a PCA10040.
I downloaded nRF52_SDK_0.9.2_dbc28c9.zip.
I want to use "ble_peripheral\ble_app_uart " sample program.
However, supporting it is PCA10036. (by readme...
I am modifying the ble_central\ble_app_hrs_c example to connect to a peripheral with an "Authentication Characteristic" that is used to initiate the peripheral-specific authentication...
