Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I notice that Gazell could only send 32 bytes per Payload in nRf51 series. So i wanted to know what can be the maximum speed i can attain using that payload.
Hi,
I would like to test the maximum efficency build, with settings like this :
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
My code is as follows:
APP_GPIOTE_INIT(4);
retcode = app_gpiote_user_register(&gpioID, 0, (1 << INT_PIN_MAXIM), interrupt);
The latter function call seems to fail with...
I have check the mesh feature on below link:
github.com/.../nRF51-ble-bcast-mesh
But it seems to work under SDK8.0, how can I make it work with SDK11 and SD130?
Thanks...
To all,
I looked through the nRF52832_PS_v1.0 product spec and I can't find any power consumption numbers for Flash erase. Does anyone know what is the Flash peak current...
I'm trying to migrate a BLE peripheral app on nRF51822 from SDK 10 and s110 to SDK 11 and s130.
I saw that the new Peer Manager does away with pstorage in favour of fstorage...
We designed a BLE device (based on SDK v10.0.0 + SoftDevice S110). From this device we do a few notifications (through sd_ble_gatts_hvx) between two connection intervals....
Hello I have some question about Keil uVision and Nordic Semiconductor SDK.
My development platform is Keil uVision v5 and my target board is nRF51-DK
I've studied many...
I can't find sample code showing how to send multiple packets per BLE interval.
Can someone share an example or point to one in the SDK?
Thanks
Hani Abidi
Hello all,
I am using the nrf51822 chip as well as an accelerometer LIS3DH. The device does advertising and turns on a LED when it is active.
The accelerometer is configured...
I have implemented multiple application timers who all automatically use the scheduler because I used:
APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE...
So im basing my project on your Android-nRF-UART-master example found in github, i don't know if its a app bug or issue regarding the circuit, but first connection is always...
I just started using the RTT and it's been a huge help. I'm working on a multilink application, and would like to have each link output to a different RTT terminal. I use...
Hi !
I'm using S130 softdevice on SDK 11 as central. I'm wondering if there are any conflits in the stack I should be warned. I know it is not allowed to start connection...
