Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello,
I am working on S120 stack with 9.0 SDK and testing with heartrate application and iPad as a peripheral. I am getting the central device as nRF51822 after central...
Do I need to implement my own timer to wrap this function? I appears that I might receive a BLE_GAP_EVT_TIMEOUT timeout event but testing has yet to reveal one.
My test...
Is there an example that is a minimal example of advertising on S110?
It might even serve one attribute that is set to a constant like '1234'.
This would help me bring...
HI
I am trying to use mkit as programmer by P20
FOR third part BLE brd
VDD---mkit.vdd
GND--mkit.gnd
SWD--P20.4
SWC--P20.5
bisides, for
P20.3(SH_VTG) connected...
We're going to be programming and debugging our prototype nRF51822 board using this adapter from Segger. It's the same connector as comes with the J-Link LITE in the dev kit...
Dear Nordic Team,
I am using Nordic DK board,
Now i want integrate UART to hid-mouse application. So that whatever data i can receive , will send to HID device without...
Hello everybody,
I'm trying to use pstorage module but it seems that the example_cb_handler function is never called when I try to store data.
I noticed similar issues...
There have been a number of other older topics with this same error message symptom, but I've tried all the solutions proposed and none have worked to solve this specific...
Hi.
I am using SD s110, ble_app_uart example from SDK10.0.0 on dk pca10028 as a peripheral. The central is a laptop running linux.
I am trying to establish a connection...
As noted here , a lower interval will give quicker connection - but at the expense of power consumption.
With a 4s interval, it seems that it is likely to take several...
Let's say I add two PPIs which both trigger off of the same event. One of these PPIs is connected to the CHG[0].EN task, and the other is connected to the CHG[0].DIS task...
In the GTT_2_Introduction nRF52 document there is a picture with text
-42 dB Selectivity (2'nd CI). As far as i concerned it's about Carrier-to-interference ratio. But what...
Hi.
I am using DK PCA10028 V1.1.0 for my devlopment. The SD is ver 8.0.0, the SDK is the latest and keil v5. The IC is nRF51422QFAC. I am trying to flash the examples from...
Hello, Is it possible to configure nRF's USART to work with Smartcards (ISO 7816)?
The ISO7816 specification defines the bit rate with the following formula:
B=(Di/Fi...
I use the " nrf51-ble-dfu-symmetric-signing " example from GitHub.
The application download over dfu works fine on the PCA10028 board.
But how can I install this bootloader...
